Embassy Flag, Idaho flag


IDAHO STATE FLAG
Idaho flags, desktop flags, flag lapel pins, flag patch, flag decal
Order all Idaho flag items from the pull down menu below or see Bulk Pricing

Idaho State flag
Order Menu

Idaho state flags are USA made.
200 denier nylon and 2-ply woven polyester (Tough-tex or Poly-Max)
Outdoor flags are finished with heading and brass grommets up to 6x10 ft, rope heading & metal thimble ends on sizes 8x12 ft and larger.
Idaho indoor flag
Idaho Indoor Flag

Nylon with pole hem and fringe
Indoor / Parade flagpoles & accessories
Idaho boat flag
Idaho boat flag, ensign, courtesy flag
12"x18" 200 denier nylon
finished with heading and brass grommets.
Idaho desktop flag
Idaho Desktop Flag
4"x6" soft nylon miniature flag mounted on a 10" black staff
with golden spear point
Idaho state flag lapel pin
Idaho state flag lapel pin
Etched & Die Struck Enamel flag lapel pins on brass
3/4" to 1" (19 to 24 mm)
Idaho friendship flag lapel pin
Idaho / USA friendship flag lapel pin
(crossed flag lapel pin)
Idaho flag decal
Idaho state flag decal
3.25" x 5" on vinyl stock w/ UV blocking inks.
Non-permanent adhesive - waterproof
.
Idaho state flag patch
Idaho state flag patch
100% embroidered including trim, 2 1/4" x 3 1/2"
Washable, sew-on, iron-on.
Desktop flag stands
Desktop Flag Stands / Bases - for 4"x6" desktop flags
# 1-7 hole black plastic, #10 & 12 hole wood

PRODUCT DESCRIPTIONS
Idaho outdoor state flags
are USA made of nylon flag material and are finished with a canvas heading and two brass grommets on the hoist side, 2 rows of stitching top and bottom sides and 4 rows of stitching on the fly side. They are attached to the flagpole by means of a halyard (rope) and flag snaps, or to smaller poles with flag fasteners. Standard sizes for outdoor state flags are 2x3 ft, 3x5 ft, 4x6 ft, 5x8 ft. and 6x10 ft.

Extra large outdoor nylon flags are offered in 8x12 ft, 10x15 ft and 12x18 ft. Production process includes a #10 white nylon rope is sewn into the 2” cotton polyester blend header. Galvanized metal thimble ends are crimped to the rope ends for attachment to the flag snaps. An additional brass grommet is placed midway on the heading for use with a third flag snap for durability and stability on the halyard.

Extreme wear outdoor state flags are produced using open weave 2-ply woven polyester, the longest wearing flag material available for daily, long-term display. This open weave material reduces fabric stress and outside fly-end shredding in high wind applications, allowing for up to double the wear of traditional nylon flags. Sizes offered are 3x5 ft, 4x6 ft and 5x8 ft. Textile trade names are Annin Flagmakers Tough-tex or Eder Flag Mfg. Poly-Max.

Idaho boat flags are nylon, 12”x18” size with 2 brass grommets.

Idaho indoor flags are available in 3x5 ft and 4x6 ft. nylon, and feature a pole sleeve with a flannel liner and a tab sewn inside the sleeve. The tab attaches to a hook or screw a top of the parade or display flagpole to keep the flag from sliding down the pole. Indoor and parade flags are finished with two-inch gold rayon fringe. These flags are also available with a pole sleeve only and no fringe (made to order, allow 2 weeks). All indoor flags are USA made.

3x5 ft indoor flags are typically displayed on either 7 ft or 8 ft poles. 4x6 ft indoor flags are typically displayed on 9 ft poles. Poles are available in polished hardwood and either silver or gold anodized aluminum. Indoor floor stands are available in either weighted ABS plastic or cast metal in gilt, brass or chrome finishes. Flagpole finials for indoor / parade poles are available in ABS plastic and both brass or chrome metal finishes.

Idaho desktop flags are made in the United States. Size is 4 x 6 inch, lightweight nylon material, hemmed all four sides, mounted on 10” black staffs with a golden spear point. Table top bases are available in black plastic to display from 1- 7 flags. Wood bases are available with either 10 holes or 12 holes to display additional flags.

Idaho stick flags, hand held mounted flags are 8 x 12 inch, lightweight nylon, fully hemmed, mounted on a ¼” x 18” black wood dowel with a golden spear point, and made in America. Sold in quantities of 12/box only, please call to order.

Idaho classroom flags for school districts are 12”x18” lightweight poly flags hemmed on all four sides and mounted on 3/8” x 30” black wood staff with golden spear tip. Sold in quantities of 12 / box only, please call to order.

FLAG DESCRIPTION / HISTORY
Year Adopted: 1907
The area that became Idaho was acquired with the Louisiana Purchase of 1803. It had status as The Territory of Idaho from 1863 until July 1890, when it was admitted as the 43rd U.S. State.

Idaho State Seal The Idaho flag contains the Great Seal of Idaho on a blue field, with a scroll underneath of gold block letters two inches high on a red band reading “State of Idaho”. The flag was adopted by the 1907 legislature. The state seal was designed in 1891 by Emma Edwards Green, daughter of John C. Edwards, a former Governor of Missouri (1844-48) and emigrant from Stockton, California. A former art student in New York, she entered a state design competition and won unanimously. The seal depicts a centered shield bearing symbolic images of the state, a woman on the left representing equality, liberty and justice, and at right, a miner, above the shield an elk's head.. A scroll above reads the Latin phrase "Esto Perpetua" (Let it be perpetual"). The state seal was updated in 1957.


About Embassy Flag
Embassy Flag copyright