Embassy Flag, Utah flag


UTAH STATE FLAG
Utah flags, desktop flags, flag lapel pins, flag patch, flag decal
Order all Utah flag items from the pull down menu below or see Bulk Pricing.

Utah state flag
Order Menu

Utah state flags are USA made.
200 denier nylon and 2-ply woven polyester (Tough-tex or Poly-Max)
Outdoor flags are finished with heading and brass grommets up to 6x10 ft, rope heading & metal thimble ends on sizes 8x12 ft and larger.
Utah indoor flag
Utah Indoor Flag
Nylon with pole hem and fringe
Indoor / Parade flagpoles & accessories
Utah boat flag
Utah boat flag, ensign, courtesy flag
12"x18" 200 denier nylon
finished with heading and brass grommets.
Utah desktop flag
Utah Desktop Flag
4"x6" soft nylon miniature flag mounted on a 10" black staff
with golden spear point
Utah flag lapel pin
Utah flag lapel pin
Etched & Die Struck Enamel flag lapel pins on brass
3/4" to 1" (19 to 24 mm)
Utah friendship flag lapel pin
Utah / USA friendship flag lapel pin
(crossed flag lapel pin)
Utah flag decal
Utah state flag decal
3.25" x 5" on vinyl stock w/ UV blocking inks.
Non-permanent adhesive - waterproof
.
Utah state flag patch
Utah state flag patch
100% embroidered including trim, 2 1/4" x 3 1/2"
Washable, sew-on, iron-on.
 
Desktop flag stands
Desktop Flag Stands / Bases - for 4"x6" desktop flags
# 1-7 hole black plastic, #10 & 12 hole wood

PRODUCT DESCRIPTIONS
Utah outdoor state flags
are USA made of nylon flag material and are finished with a canvas heading and two brass grommets on the hoist side, 2 rows of stitching top and bottom sides and 4 rows of stitching on the fly side. They are attached to the flagpole by means of a halyard (rope) and flag snaps, or to smaller poles with flag fasteners. Standard sizes for outdoor state flags are 2x3 ft, 3x5 ft, 4x6 ft, 5x8 ft. and 6x10 ft.

Extra large outdoor nylon Utah flags are offered in 8x12 ft, 10x15 ft and 12x18 ft. Production process includes a #10 white nylon rope is sewn into the 2” cotton polyester blend header. Galvanized metal thimble ends are crimped to the rope ends for attachment to the flag snaps. An additional brass grommet is placed midway on the heading for use with a third flag snap for durability and stability on the halyard.

Extreme wear outdoor state flags are produced using open weave 2-ply woven polyester, the longest wearing flag material available for daily, long-term display. This open weave material reduces fabric stress and outside fly-end shredding in high wind applications, allowing for up to double the wear of traditional nylon flags. Sizes offered are 3x5 ft, 4x6 ft and 5x8 ft. Textile trade names are Annin Flagmakers Tough-tex or Eder Flag Mfg. Poly-Max.

Utah boat flags are nylon, 12”x18” size with 2 brass grommets.

Utah indoor flags are available in 3x5 ft and 4x6 ft. nylon, and feature a pole sleeve with a flannel liner and a tab sewn inside the sleeve. The tab attaches to a hook or screw a top of the parade or display flagpole to keep the flag from sliding down the pole. Indoor and parade flags are finished with two-inch gold rayon fringe. These flags are also available with a pole sleeve only and no fringe (made to order, allow 2 weeks). All indoor flags are USA made.

3x5 ft indoor flags are typically displayed on either 7 ft or 8 ft poles. 4x6 ft indoor flags are typically displayed on 9 ft poles. Poles are available in polished hardwood and either silver or gold anodized aluminum. Indoor floor stands are available in either weighted ABS plastic or cast metal in gilt, brass or chrome finishes. Flagpole finials for indoor / parade poles are available in ABS plastic and both brass or chrome metal finishes.

Utah desktop flags are made in the United States. Size is 4 x 6 inch, lightweight nylon material, hemmed all four sides, mounted on 10” black staffs with a golden spear point. Table top bases are available in black plastic to display from 1- 7 flags. Wood bases are available with either 10 holes or 12 holes to display additional flags.

Utah stick flags, hand held mounted flags are 8 x 12 inch, lightweight nylon, fully hemmed, mounted on a ¼” x 18” black wood dowel with a golden spear point, and made in America. Sold in quantities of 12/box only, please call to order.

Utah state classroom flags for school districts are 12”x18” lightweight poly flags hemmed on all four sides and mounted on 3/8” x 30” black wood staff with golden spear tip. Sold in quantities of 12 / box only, please call to order.

FLAG DESCRIPTION / HISTORY
Year Adopted: 1913. The original Utah State Flag consisted of a solid white state seal on a light blue background which was adopted by the State Legislature in 1896 and revised in 1913. The current Utah State Flag was originally designed for the battleship Utah in 1912. It was later made the official flag of Utah when Governor William Spry signed House Joint Resolution I in 1913. The Utah State Flag has a blue background with the (ed. inner portion of the) State Seal inscribed in the center within a single gold circle. In 1922, changes were made in the state flag which were not consistent with the 1913 statute. The Utah State Flag Concurrent Resolution (Utah State Legislature, 2011 General Session, H.C.R. 2 Enrolled) reaffirmed the 1913 statute and encouraged that state flags be manufactured according to the law. (ref; pioneer.utah.gov)

Utah State Seal

The inner portion of the Great Seal is used on the flag.

"The Great Seal of the State of Utah shall be ......of the following device; the center a shield and perched thereon an American Eagle with outstretching wings; the top of the shield pierced by six arrows crosswise; under the arrows the motto "INDUSTRY"; beneath the motto a beehive, on either side growing sego lilies; below the figures "1847"; on each side of the shield an American Flag.; encircling all, near the outer edge of the seal, beginning at the lower left-hand portion, the words, "THE GREAT SEAL OF THE STATE OF UTAH", with the figures "1896" at the base. The State Shield was adopted in 1896. (ref; pioneer.utah.gov)


About Embassy Flag
Embassy Flag copyright